Home | About us | Editorial board | Search | Ahead of print | Current issue | Archives | Submit article | Instructions| Reviewers

  Home Print this page Email this page Small font sizeDefault font sizeIncrease font size Users Online: 177    

Table of Contents   
Year : 2017  |  Volume : 7  |  Issue : 9  |  Page : 125-136
Role of cone beam computed tomography in diagnosis and treatment planning in dentistry: An update

1 Department of Dentistry, All India Institute of Medical Sciences, Rishikesh, Uttarakhand, India
2 Department of Dentistry and Maxillofacial Surgery, All India Institute of Medical Sciences, Rishikesh, Uttarakhand, India
3 Division of Prosthodontics and Restorative Dentistry, Faculty of Dentistry, McGill University, Montreal, Canada

Date of Submission24-Dec-2016
Date of Acceptance25-Oct-2017
Date of Web Publication30-Nov-2017

Correspondence Address:
Kelvin I Afrashtehfar
Faculty of Dentistry, McGill University, Stratchona Anatomy and Dentistry Building, 3640 University Street, Rm M/65, Montreal, Quebec, H3A 0C7
Login to access the Email id

Source of Support: None, Conflict of Interest: None

DOI: 10.4103/jispcd.JISPCD_516_16

Rights and Permissions


Accurate diagnosis and treatment planning are the backbone of any medical therapy; for this reason, cone beam computed tomography (CBCT) was introduced and has been widely used. CBCT technology provides a three-dimensional image viewing, enabling exact location and extent of lesions or any anatomical region. For the very same reason, CBCT can not only be used for surgical fields but also for fields such as endodontics, prosthodontics, and orthodontics for appropriate treatment planning and effective dental care. The aim and clinical significance of this review are to update dental clinicians on the CBCT applications in each dental specialty for an appropriate diagnosis and more predictable treatment.

Keywords: Anatomical variation, cone beam computed tomography, dental technology, pathology, radiology, three-dimensional, X-ray

How to cite this article:
Shukla S, Chug A, Afrashtehfar KI. Role of cone beam computed tomography in diagnosis and treatment planning in dentistry: An update. J Int Soc Prevent Communit Dent 2017;7, Suppl S3:125-36

How to cite this URL:
Shukla S, Chug A, Afrashtehfar KI. Role of cone beam computed tomography in diagnosis and treatment planning in dentistry: An update. J Int Soc Prevent Communit Dent [serial online] 2017 [cited 2022 Jun 28];7, Suppl S3:125-36. Available from: https://www.jispcd.org/text.asp?2017/7/9/125/219498

   Introduction Top

Wilhelm C. Röntgen discovered electromagnetism in 1895 in a wavelength range (the X-rays) which became a very important diagnostic tool.[1] This discovery unleashed a great source of knowledge of the human body breaking the constraints of medical science and enabling doctors to diagnose and treat pathologies accurately. It was after 14 years that X-rays were recognized in dentistry by Dr. Walkhoff, a dentist in Braunschweig, Germany. The discovery of X-rays was the basis for improved methods of scientific evaluation such as the cone beam computed tomography (CBCT). Interestingly, this technology took almost 40 years to evolve and become available for clinicians.

CBCT has evolved from CT scan; a technique invented in 1967 by the British engineer Godfrey Hounsfield.[2] The first prototype of clinical CBCT scanner was originally devised as a cost-effective and efficient method for obtaining cross-sectional three-dimensional (3D) images for radiotherapy and later (1982) for angiography.[3] CBCT's commercial availability was delayed for a decade and was first introduced in Europe in 1998 and the US in 2001.[3] Columbia Scientific Inc., introduced 3D dental software in dentistry in 1988, and 2 years later, CBCT started to appear in dental research publications.[4] With CBCT's introduction in dentistry, dental clinicians could not only have profound knowledge of oral pathology but could also enhance the access to a detailed view of the underlying structures and their relations. This 3D image was groundbreaking since the process of decision-making became simpler and the recognition of the bony defects from different angles became easier.

The aim of this manuscript is to describe the CBCT function concept and its application in dental and maxillofacial conditions.

   Materials and Methods Top

This narrative review gathered literature from peer-reviewed articles published in indexed journals available in PubMed and other web-based resources. The article and literature used for this publication has been summarized in [Table 1].
Table 1: Summary of literature used for this publication

Click here to view

Applications in dentistry

Oral surgery

An oral surgeon can analyze the size, extent, and location of a tumor or cyst, its penetration into surrounding structures, and relation to vital structures such as nerves and blood vessels [Figure 1]. CBCT also helps in the assessment of impacted teeth and supernumerary in terms of its location and relation to vital structures.[5] The clinician can also detect changes in the bony deformities related to bisphosphonate-associated osteonecrosis of the jaw, bone grafts, and paranasal sinuses; in cases of obstructive sleep apnea, it helps to form a volume surface rendering of the windpipe.[5] CBCT has the ability to provide attention to details, thus, becomes the technology of choice for midface fracture cases e.g., gunshot wounds, orbital fracture management, interoperative visualization of the facial bones after fracture [Figure 2], and intraoperative navigation during surgical procedures.[6],[7],[8]
Figure 1: Destruction of the body – parasymphysis left mandibular region due to an intrabony tumor

Click here to view
Figure 2: Multiple fractures involving the naso-orbitoethmoidal region, bilateral Le Fort 2 and 3 levels and a bilateral high Le Fort 1 fracture along with a left parasymphysis fracture of the mandible

Click here to view

In cases of temporomandibular joint disorders and dysfunctioning related to trauma, pain, dysfunction, fibro-osseous ankylosis, detecting condylar cortical erosion, cysts, and visualization of soft tissue (ST), CBCT becomes the imaging device of choice.[9]


CBCT provides a higher degree of predictability of implant placement because of its accuracy for evaluation. The clinician can evaluate the height and width of the bone present to place an implant [Table 2] and [Figure 3]. In peri-implantitis cases, the amount of bone surrounding the implant can be assessed previous to probing, providing such important information as radiolucency.[10],[11]
Figure 3: Use of cone beam computed tomography in planning the tridimensional placement of four implants in the anterior zone

Click here to view
Table 2: Cone beam computed tomography used in the treatment of implantology

Click here to view


An orthodontist can use CBCT for the assessment of the position of unerupted teeth, particularly for impacted ones, especially in cases of maxillary impacted canines where knowing exactly the tooth position results in accurate treatment planning [Figure 4]. The angulation is appreciated well in these 3D images, which would be difficult to appreciate on conventional radiographs even when taken in two different planes. It also helps in identification of any resorption of adjacent teeth (i.e., where maxillary canines are ectopic and incisor roots are suspected of having undergone resorption).[12]
Figure 4: Three-dimensional view of both maxillary and mandibular arches depicting amount of bone present, craters, furcation, and crestal bone loss

Click here to view

Other applications of CBCT in orthodontics are cleft palate assessment, resorption related to impacted teeth, rapid maxillary expansion, 3D cephalometry, surface imaging integration, airway assessment, age assessment, and investigation of orthodontic-associated paraesthesia.[13] In cases where mini-screw implants are placed for anchorage, CBCT is used to analyze bone dimensions and precise location of placement to minimize complications.[14]


CBCT can also be used for caries diagnosis since caries detection and depth evaluation in approximal and occlusal lesions are improved considerably. However, its application in endodontic-metallic restoration would produce artifacts reducing diagnostic accuracy.[15] CBCT imaging for caries should be limited to nonrestored teeth. Sensitivity may increase with CBCT but it should not be at the cost of specificity.[15] CBCT in endodontics can be used for identification and measurement of the extent of periapical lesions [16] and it also differentiates solid from fluid-filled lesions (e.g., periapical granulomas from cysts) using grayscale values in the lesions.[15] CBCT plays an important role in establishing successful endodontic therapy by identification of all root canals so that they can be accessed, cleaned, shaped, and obturated.[16] It helps in identification of prevalence of a second mesiobuccal canal (MB2) in maxillary first molars and also multiple and accessory canals (aberrant pulpal anatomy, e.g., dens invaginatus) in any other teeth.[15] It also helps in differentiation of pathosis from normal anatomy and relationships with important anatomical structures. CBCT also plays an important role in the diagnosis and management of root fractures, luxation and/or displacement, and alveolar fracture.[17],[18],[19],[20],[21],[22]


In periodontics, CBCT detects the amount of bone present, craters, furcation, crestal bone loss, fenestrations, and dehiscences [Figure 5]. In spite of its usefulness in this field, CBCT is not indicated as a routine method of imaging periodontal bone support. However, limited volume, high-resolution CBCT may be indicated in selected cases of infrabony defects and furcation lesions, where clinical and conventional radiographic examinations do not provide the information needed for management; thus, it may have a role to play in the management of complex periodontal defects for which surgery is the treatment option.[13],[15] CBCT can also be used within a period of 1 month for postoperative defect fill or bone density evaluation, which cannot be detected through normal radiographs, and it can also replace subtraction radiography.[15]
Figure 5: Both permanent upper canines are impacted with the crown facing toward the palatal aspect and the roots more toward the buccal aspect

Click here to view

CBCT can help in identifying bone defect size and early signs of periodontitis by assessing periodontal ligament space, measurement of gingival tissue, and the dimensions of the dentogingival unit.[23] This method is called ST-CBCT and helps to visualize and measure precisely distances corresponding to the hard and STs of the periodontium and dentogingival attachment apparatus. With ST-CBCT, gingival margin and the facial bone crest, gingival margin and the cementoenamel junction (CEJ), and CEJ and facial bone crest can be determined.[23],[24],[25]

Forensic dentistry

CBCT can also be applied in the field of forensic dentistry for accurate age estimation for every person of the legal system (including those who have passed away). To estimate accurate age, tooth has to be sectioned to identify morphological changes; as with age, internal layers of the tooth (dentin, cementum, and pulp) illustrate physiological and pathological changes.[26] However, with CBCT, such aggressive methods are not required.[27]

Safety concerns

It is paramount that as low as reasonably achievable (ALARA) principle is followed during diagnosis, as far as the radiation dose of CBCT imaging is concerned.[28] Use of CBCT for examination must be justified for each patient as the examination is dose dependent; i.e., higher doses of radiation may also be applied depending on the lesion to be examined, but higher radiation increases risks. Thus, CBCT should only be used when the question for which imaging is required cannot be answered adequately by lower dose conventional (traditional) radiography.[28] Therefore, it is necessary to ensure that patient doses are monitored on a regular basis and compared to agreed standards. Standard dose levels are normally referred to as diagnostic reference levels, and a dose of 4 mGy of SRL is recommended as the absorbed dose in air measured at the end of the spacer cone for a standard maxillary molar projection.[28]

By 1897, Kells reported that long exposures to X-rays caused a mild skin irritation, similar to sunburn, and early X-ray machines needed adjustment for each use so that the operator placed his hand between the actively radiating tube and the film plate. Kells took radiographs in this manner for 12 years, after which he developed cancerous tumors on his fingers. Thus, concerns about radiation exposure, especially when it is done once in a lifetime are inconsequential; furthermore, beyond 80 years of age, the risk becomes negligible because the latent period between X-ray exposure and the clinical presentation of a tumor would probably exceed the lifespan of a patient.[29] In contrast, the tissues of younger people are more radiosensitive and their prospective lifespan is likely to exceed the latent period. However, the ALARA principle should be kept in mind and should be followed with each exposure.

Limitations of cone beam computed tomography imaging

While there has been enormous interest on CBCT, this technology currently has limitations too related to the “cone beam” projection geometry, detector sensitivity, and contrast resolution.[30] These parameters create an inherent image (known as noise) that reduces image clarity in such a way that current systems are unable to record ST contrast at the relatively low dosages applied for maxillofacial imaging; however, with advanced systems, it can be achieved.[30] Another factor that impairs CBCT image quality is image artifacts, such as streaking, shading, rings, and distortion.[31] Streaking and shading artifacts due to high areas of attenuation and inherent spatial resolution may limit adequate visualization of structures in the oral and maxillofacial region.[31]

Another limitation is the cost of the equipment and investment in the area where it is to be installed, as CBCT causes scattering of the radiation, especially when larger tissue is being evaluated, causing polydirectional Compton scattering. Thus, it needs lead barriers to be placed, adding to the investment.[31]

Another disadvantage is the poor quality in ST assessment.[13] The dynamic range of CBCT for contrast resolution can reach only 14-bit maximally.[32] To accurately read a ST phenomenon, a 24-bit contrast resolution is needed.[29] In addition, unlike multidetector CT, the Hounsfield units of tissue density are not calibrated on CBCT, which makes it unreliable to compare tissue density based on CT numbers generated from different CBCT units.[32]

   Conclusion Top

From the aforementioned literature review, along with the advantages and disadvantages of CBCT, it seems that CBCT may not be the best imaging modality to evaluate STs; however, there are situations in which CBCT can help such as analysis of ST airway constrictions and obstructions for patients suffering from sleep apnea, other ST evaluations for orthodontic treatment and periodontal treatment,[33],[34] and detection of healed root fractures.[35] The development and rapid commercialization of CBCT technology has undoubtedly increased practitioners' use of CBCT, as it is capable of providing accurate, submillimeter resolution images in formats enabling 3D visualization of the complexity of the maxillofacial region. It also provides clinicians with a modality that extends maxillofacial imaging from diagnosis to image guidance for operative and surgical procedures. Today, Wilhelm C. Röntgen's discovery through its evolution is providing diagnostic efficacy that can result in improved therapeutic efficiency in the medical and dental fields.

Financial support and sponsorship


Conflicts of interest

There are no conflicts of interest.

   References Top

Filler AG. The history, development, and impact of computed imaging in neurological diagnosis and neurosurgery: CT, MRI and DTI. Nat Proc 2010;7:1-85.  Back to cited text no. 1
Bhattacharyya KB. Godfrey Newbold Hounsfield (1919–2004): The man who revolutionized neuroimaging. Ann Indian Acad Neurol 2016;19:448-50.  Back to cited text no. 2
[PUBMED]  [Full text]  
Liguori C, Frauenfelder G, Massaroni C, Saccomandi P, Giurazza F, Pitocco F, et al. Emerging clinical applications of computed tomography. Med Devices (Auckl) 2015;8:265-78.  Back to cited text no. 3
Orentlicher G, Goldsmith D, Abboud M. Computer-guided planning and placement of dental implants. Atlas Oral Maxillofac Surg Clin North Am 2012;20:53-79.  Back to cited text no. 4
Ogawa T, Enciso R, Shintaku WH, Clark GT. Evaluation of cross-section airway configuration of obstructive sleep apnea. Oral Surg Oral Med Oral Pathol Oral Radiol Endod 2007;103:102-8.  Back to cited text no. 5
Araki M, Kameoka S, Matsumoto N, Komiyama K. Usefulness of cone beam computed tomography for odontogenic myxoma. Dentomaxillofac Radiol 2007;36:423-7.  Back to cited text no. 6
Nair MK, Pettigrew JC Jr., Mancuso AA. Intracranial aneurysm as an incidental finding. Dentomaxillofac Radiol 2007;36:107-12.  Back to cited text no. 7
Bianchi A, Muyldermans L, Di Martino M, Lancellotti L, Amadori S, Sarti A, et al. Facial soft tissue esthetic predictions: Validation in craniomaxillofacial surgery with cone beam computed tomography data. J Oral Maxillofac Surg 2010;68:1471-9.  Back to cited text no. 8
Swennen GR, Mommaerts MY, Abeloos J, De Clercq C, Lamoral P, Neyt N, et al. Acone-beam CT based technique to augment the 3D virtual skull model with a detailed dental surface. Int J Oral Maxillofac Surg 2009;38:48-57.  Back to cited text no. 9
Uchida Y, Noguchi N, Goto M, Yamashita Y, Hanihara T, Takamori H, et al. Measurement of anterior loop length for the mandibular canal and diameter of the mandibular incisive canal to avoid nerve damage when installing endosseous implants in the interforaminal region: A second attempt introducing cone beam computed tomography. J Oral Maxillofac Surg 2009;67:744-50.  Back to cited text no. 10
Worthington P, Rubenstein J, Hatcher DC. The role of cone-beam computed tomography in the planning and placement of implants. J Am Dent Assoc 2010;141 Suppl 3:19S-24S.  Back to cited text no. 11
Alqerban A, Hedesiu M, Baciut M, Nackaerts O, Jacobs R, Fieuws S, et al. Pre-surgical treatment planning of maxillary canine impactions using panoramic vs. cone beam CT imaging. Dentomaxillofac Radiol 2013;42:9.  Back to cited text no. 12
Dang V. Focus on cone beam computed tomography. Dent Pract 2009;9:10-2.  Back to cited text no. 13
Bittencourt LP, Raymundo MV, Mucha JN. The optimal position for insertion of orthodontic miniscrews. Rev Odonto Cienc 2011;26:133-8.  Back to cited text no. 14
Tyndall DA, Rathore S. Cone-beam CT diagnostic applications: Caries, periodontal bone assessment, and endodontic applications. Dent Clin North Am 2008;52:825-41, vii.  Back to cited text no. 15
Scarfe WC, Levin MD, Gane D, Farman AG. Use of cone beam computed tomography in endodontics. Int J Dent 2009;2009:634567.  Back to cited text no. 16
Cohenca N, Simon JH, Roges R, Morag Y, Malfaz JM. Clinical indications for digital imaging in dento-alveolar trauma-part 1: Traumatic injuries. Dent Traumatol 2007;23:95-104.  Back to cited text no. 17
Cotton TP, Geisler TM, Holden DT, Schwartz SA, Schindler WG. Endodontic applications of cone-beam volumetric tomography. J Endod 2007;33:1121-32.  Back to cited text no. 18
John V. Non-surgical management of infected type III dens invaginatus with vital surrounding pulp using contemporary endodontic techniques. Aust Endod J 2008;34:4-11.  Back to cited text no. 19
Tsurumachi T, Honda K. A new cone beam computerized tomography system for use in endodontic surgery. Int Endod J 2007;40:224-32.  Back to cited text no. 20
Young GR. Contemporary management of lateral root perforation diagnosed with the aid of dental computed tomography. Aust Endod J 2007;33:112-8.  Back to cited text no. 21
Patil S, Keshava Prasad BS, Shashikala K. Cone beam computed tomography: Adding three dimensions to endodontics. Int Dent Med J Adv Res 2015;1:1-6.  Back to cited text no. 22
Mohan R, Singh A, Gundappa M. Three-dimensional imaging in periodontal diagnosis-utilization of cone beam computed tomography. J Indian Soc Periodontol 2011;15:11-7.  Back to cited text no. 23
[PUBMED]  [Full text]  
Afrashtehfar KI. Using bi-dimensional and tri-dimensional radiography in dentistry. Rev ADM 2012;69:114-9.  Back to cited text no. 24
Afrashtehfar KI, Cárdenas-Bahena JT, Afrashtehfar CD. Predictable immediate loading of mandibular implants. Tex Dent J 2013;130:596-607.  Back to cited text no. 25
Bérgamo AL, de Queiroz CL, Sakamoto HE, Alves da Silva RH. Dental age estimation methods in forensic dentistry: Literature review. Peertechz J Forensic Sci Technol 2016;1:17-22.  Back to cited text no. 26
Nodehi D, Pahlevankashi M, Moghaddam MA, Nategh B. Cone beam computed tomography functionalities in dentistry. Int J Contemp Dent Med Rev 2015;2015:1-8.  Back to cited text no. 27
European Commission 2012. Cone Beam CT for Dental and Maxillofacial Radiology. Evidence-Based Guidelines. Available from: http://www.ec.europa.eu/energy/nuclear/radiation_protection/doc/com_2011_0593.pdf. [Last accessed on 2017 Oct 01].  Back to cited text no. 28
White SC, Pharoah MJ. Oral Radiology – Principles and Interpretation. St. Louis: CV Mosby; 2014.  Back to cited text no. 29
Shaibah WI, Ibrahim AY, Jastaniah SD. Physical measurements for the accuracy of cone-beam CT in dental radiography. Open J Med Image 2014;4:57-64.  Back to cited text no. 30
Adibi S, Zhang W, Servos T, O'Neill PN. Cone beam computed tomography in dentistry: What dental educators and learners should know. J Dent Edu 2012;76:1437-42.  Back to cited text no. 31
Gupta R, Gupta P, Puri G, Konidena A, Dixit A, Patil DJ, et al. Use of cone beam computed tomography in dentistry. Int J Appl Res 2015;1:482-4.  Back to cited text no. 32
Macdonald-Jankowski DS, Orpe EC. Some current legal issues that may affect oral and maxillofacial radiology. Part 2: Digital monitors and cone-beam computed tomography. J Can Dent Assoc 2007;73:507-11.  Back to cited text no. 33
Scarfe WC, Farman AG. Cone-beam computed tomography. In: Oral Radiology: Principles and Interpretation. 6th ed. St. Louis, MO: Mosby Elsevier; 2009.  Back to cited text no. 34
Orhan K, Aksoy U, Kalender A. Cone-beam computed tomographic evaluation of spontaneously healed root fracture. J Endod 2010;36:1584-7.  Back to cited text no. 35


  [Figure 1], [Figure 2], [Figure 3], [Figure 4], [Figure 5]

  [Table 1], [Table 2]

This article has been cited by
1 Reliability and accuracy of a method for measuring temporomandibular joint condylar volume
Justin J. Kim,Manuel O. Lagravere,Neelambar R. Kaipatur,Paul W. Major,Dan L. Romanyk
Oral Surgery, Oral Medicine, Oral Pathology and Oral Radiology. 2021; 131(4): 485
[Pubmed] | [DOI]
2 The diagnostic value of orthopantomograms in detecting resorption of lateral incisors associated with ectopic canines: a CBCT study
Catherine Maria Hershaw, Nizar Mhani, Angharad Brown
Journal of Orthodontics. 2021; : 1465312521
[Pubmed] | [DOI]
3 Assessment of Immediate Skeletal Changes after Alternate Rapid Maxillary Expansion and Constriction – A Case Report
Shilpa Venkatesh Pharande
Journal of Evolution of Medical and Dental Sciences. 2021; 10(34): 2954
[Pubmed] | [DOI]
4 Assessment of interobserver reliability in localization of hard and soft tissue landmarks and three-dimensional measurements of the upper airway based on these landmarks using CBCT images
Jangam Daya K,Talreja Kajol M,Garcha Vikram,Patil Abhijeet V,Swatantramath Sunaina M,Bahadure Pranali B
IP International Journal of Maxillofacial Imaging. 2021; 7(2): 54
[Pubmed] | [DOI]
5 Evaluation of Radiolucent Lesions Associated with Impacted Teeth: A Retrospective Study
Hulya Cakir Karabas , Ilknur Ozcan, Merva Soluk Tekkesin, Sedef Ayse Tasyapan, Beliz Guray, Murat Mert Atapek
Current Medical Imaging Formerly Current Medical Imaging Reviews. 2021; 16(10): 1332
[Pubmed] | [DOI]
Selcuk Dental Journal. 2020;
[Pubmed] | [DOI]
7 Accuracy of linear measurements using low dose cone beam computed tomography protocol versus direct skull linear measurements: An in vitro study
Nora Aly Al Abbady,Reham Mohamed Hamdy,Sahar Hosny El Dessouky
F1000Research. 2019; 8: 25
[Pubmed] | [DOI]
8 Vertical Tooth Root Fracture Detection through Cone-beam Computed Tomography: An Umbrella Review Protocol Testing Four Hypotheses
Kelvin Ian Afrashtehfar,David MacDonald
The Open Dentistry Journal. 2019; 13(1): 449
[Pubmed] | [DOI]
9 The efficacy of metal artifact reduction (MAR) algorithm in cone-beam computed tomography on the diagnostic accuracy of fenestration and dehiscence around dental implants
Mahnaz Sheikhi,Parichehr Behfarnia,Mahdis Mostajabi,Naeimeh Nasri
Journal of Periodontology. 2019;
[Pubmed] | [DOI]


Print this article  Email this article
    Similar in PUBMED
   Search Pubmed for
   Search in Google Scholar for
 Related articles
    Article in PDF (1,481 KB)
    Citation Manager
    Access Statistics
    Reader Comments
    Email Alert *
    Add to My List *
* Registration required (free)  

    Materials and Me...
    Article Figures
    Article Tables

 Article Access Statistics
    PDF Downloaded1945    
    Comments [Add]    
    Cited by others 9    

Recommend this journal